Caracterización de la curva esfuerzo-deformación de prismas de mampostería con bloques de concreto de 20x20x40 cm bajo carga axial
Cargando...
Archivos
Fecha
2023
Autores
Director
Título de la revista
ISSN de la revista
Título del volumen
Publicador
Páginas
Resumen
El presente estudio tiene como propósito Caracterizar la curva de esfuerzo-deformación que muestra el comportamiento en compresión axial de prismas de mampostería de concreto utilizando bloques de 200x200x400 mm por medio de pruebas experimentales para verificar si los valores específicos de diseño son adecuados. Para esto, se utilizaron prismas de mampostería conformados por bloques de concreto de 20 cm de espesor, clase A. morteros tipo M, N y S así como prismas con concreto de relleno y sin este (rellenos y vacíos) para un total de 6 combinaciones de prismas fallados a compresión; Relacionando la resistencia de los componentes con la resistencia del prisma e identificando el módulo de elasticidad y deformación ultima de los prismas. Los materiales que conforman los prismas cumplen con los valores de resistencia mínima indicados en el CSCR 10-14 y los datos generados en esta investigación permiten comparar los parámetros de diseño de la mampostería presentes en la normativa internacional con el comportamiento del material nacional utilizado. Los resultados obtenidos amplíen la muestra de datos de materiales nacionales para futuras investigaciones u otros proyectos que los requieran.
Inglés: The purpose of this study is to characterize the stress-strain curve that shows the behavior in axial compression of concrete masonry prisms using 200x200x400 mm blocks through experimental tests to verify if the specific design values are adequate. For this, masonry prisms made up of 20 cm thick concrete blocks, class A, type M, N and S mortars, as well as prisms with and without concrete filling (filled and empty) were used for a total of 6 combinations of compression failed prisms; Relating the resistance of the components with the resistance of the prism and identifying the modulus of elasticity and ultimate deformation of the prisms. The materials that make up the prisms comply with the minimum resistance values indicated in CSCR 10-14 and the data generated in this investigation allow comparing the design parameters of the masonry present in international regulations with the behavior of the national material. used. The results obtained expand the data sample of national materials for future research or other projects that require them.
Inglés: The purpose of this study is to characterize the stress-strain curve that shows the behavior in axial compression of concrete masonry prisms using 200x200x400 mm blocks through experimental tests to verify if the specific design values are adequate. For this, masonry prisms made up of 20 cm thick concrete blocks, class A, type M, N and S mortars, as well as prisms with and without concrete filling (filled and empty) were used for a total of 6 combinations of compression failed prisms; Relating the resistance of the components with the resistance of the prism and identifying the modulus of elasticity and ultimate deformation of the prisms. The materials that make up the prisms comply with the minimum resistance values indicated in CSCR 10-14 and the data generated in this investigation allow comparing the design parameters of the masonry present in international regulations with the behavior of the national material. used. The results obtained expand the data sample of national materials for future research or other projects that require them.
Descripción
Proyecto de graduación (licenciatura en ingeniería civil)--Universidad de Costa Rica. Facultad de Ingeniería. Escuela de Ingeniería Civil, 2023
Palabras clave
ANALISIS ESTRUCTURAL (INGENIERIA), DEFORMACIONES (MECANICA), ELASTICIDAD, ESFUERZO Y TENSION, MAMPOSTERIA DE HORMIGON - DISEÑO Y CONSTRUCCION - COSTA RICA, MAMPOSTERIA DE HORMIGON - PROPIEDADES ELASTICAS, MAMPOSTERIA DE HORMIGON - PRUEBAS, RESISTENCIA DE MATERIALES - PRUEBAS